What to get your skateboard trucks off with?

Era Satterfield asked a question: What to get your skateboard trucks off with?
Asked By: Era Satterfield
Date created: Sun, Feb 28, 2021 12:38 PM
Date updated: Wed, Sep 28, 2022 1:23 PM


Top best answers to the question «What to get your skateboard trucks off with»

  • You can use pliers for this, or when using your skateboard tool, use the smallest socket. Place it on any of the nuts of your skateboard truck, then put the screwdriver to the screw inside that nut. You’ll need two hands on one side of your skateboard for stability as you put force into taking the bolts off.

How do you loosen the trucks on a skateboard?

  • - Turn it clockwise to tighten the trucks, getting tighter turning. - Turn it counter-clockwise to loosen the trucks, getting a softer turning feel. - Make sure you tighten the trucks in very small increments (perhaps a quarter of a turn at a time before checking the board again), because a little bit of turning ...


Those who are looking for an answer to the question «What to get your skateboard trucks off with?» often ask the following questions:

❓ Should your skateboard trucks squeak?

Squeaking. It's inevitable for all riders. At some point, you'll be cruising along on your longboard skateboard deck, usually doing some aggressive carving or pumping and all you hear is “squeak squeak” as you turn.

❓ What happens when your skateboard trucks shift?

  • When rolling you can turn the skateboard by shifting your weight to one side of the board or the other. When you shift your weight the bushings on the truck will compress on the one side. This allows the hanger to pivot from the pivot bushing and rotate around the kingpin.

❓ What do you clean skateboard trucks with?

Your skateboard's bearings need to be lubricated with grease or oil to function properly. That means that soap and water won't do the trick here – you'll need a solvent, such as acetone, isopropyl alcohol or rubbing alcohol to get them clean – and you'll need to re-grease them once you've finished.

9 other answers

In this guide, I’ll be showing you how to take trucks off a skateboard the easy way. Take Trucks Off a Skateboard. To begin, you’ll need the following three items: A screwdriver; A skateboard, of course; A skate tool; To start taking off the truck, you will put the truck in horizontal position. This makes it a little bit easier.

Add risers to get the board higher and reduce vibrations. Risers are attached between your trucks and your board, providing lift for tricks. Furthermore, risers you will dampen landing vibrations, though the higher board will take some getting used. Higher trucks can make it harder, however, to grind.

Take Off Your Trucks. Once all the nuts and bolts are gone from the skateboard truck, take it off its screws. Make sure that when you’re taking it off, you do it gently to prevent the board or trucks from getting damaged. When you’ve taken off the truck, you’ll have a clean board with eight screws sticking out from it.

Next, using your thumb, push the skateboard screws down through the deck and through the holes in the skateboard trucks. Using your fingers, put the hardware nuts on the ends of the screws, and turn them until you can't anymore. Once all the nuts are in place, use your skate tools and tighten the screws the same way you removed them. You should have your new skateboard trucks freshly installed onto your skateboard deck, and be ready to ride!

Bushings give the truck stability and allow you to customize the way your trucks turn. Hard bushings restrict your turn to for better stability while soft bushings allow a less stable, but more responsive turn. Shop Skateboard Bushings. Bones HardCore Medium Skate Bushings (2 Truck Set) white $9.95.

If you want loose trucks, super glue the nut down or try to find soft bushings or something that will allow you to get your trucks looser. Or you can shave new bushings down, take off new bushings and rub them on the cement and kind of shave off the edges and that helps too.

So when should you replace your skateboard trucks? You should replace your trucks when they are warped, have small cracks, bent axles or damaged baseplates. Sometimes you can replace parts like the kingpin, nuts, baseplate, washers, bushings, pivot cup or hangar without having to buy a completely new set.

Assembly of skateboard trucks and wheels. Both truck assemblies will have wheels installed with proper speed washers and torqued to the appropriate tolerance. Installing both truck assemblies to the gripped deck and assuring proper torque tolerance on all hardware. An autographed Warehouse Skateboards hang tag from your builder.

Grip tape works well to give your feet traction on the board, even when wet. But grip tape can lose adhesion over time with repeated wetting and drying. If that happens, the tape will start to peel off the deck. Skateboard trucks can withstand water for some time, but if they get wet too frequently, they will soon start to rust.

Your Answer

We've handpicked 25 related questions for you, similar to «What to get your skateboard trucks off with?» so you can surely find the answer!

Do you have to be tight with your skateboard trucks?
  • If you are a beginner, you may need to keep the tightness of your trucks somewhere in the middle. If your skates are too loose, it might lead to accidents which you definitely don’t want. On the other hand, if your skates are too tight, you may not be able to control your skates properly.
What size should your trucks be for skateboard?

Medium height skateboard trucks are great for all-around skateboarding. Suitable for skate ...

Can you replicate carver trucks with standard skateboard trucks?

Some say Carver trucks can compete with dedicated LDP (long-distance pumping) and slalom setups e.g. wedged Tracker trucks. The Carver trucks are nevertheless surf trucks at heart. They can be used for surf training and let you drive off the back foot like on a surfboard. Read on for differences between the CX and C7. Carver CX surf truck

Do skateboard trucks come with bushing?

Bushings are a very important part of skateboard trucks. Every truck is equipped with two bushings – the street-facing top bushing, and the board-facing bottom bushing… Don't worry though, all skateboard trucks come already equipped with bushings.

Do skateboard trucks come with hardwear?

Each skateboard needs two trucks that are attached via special hardware to the underside of the board. Skateboard trucks allow the rider to turn the board to the right or left depending on their weight adjustment, and make it possible to perform grinds on rails, ledges, and ramp coping. Skateboard trucks are typically made of aluminum alloy, and ...

Do skateboard trucks work with longboards?

In theory, drop-through decks work with any kind of skateboard trucks. However, we strongly recommend a proper longboard (“RKP”) truck rather than a regular “Street Style” truck. Regular Street trucks don’t turn enough for a drop-through, and often they make the board too low.

How to know what size your skateboard trucks are?

To determine the width of a skateboard truck, you measure the width of the axle (outer width) and the width of the hanger (inner width). The trucks should always fit the width of your Skateboard.

How to make your own skateboard trucks?
  • Use an old board to properly drill holes for the trucks. Trucks are the big metal pieces that hold your wheels in place. Simply place an old deck over the new board and use a pencil to mark the location of the holes. Using a straight-drill, drill each hole straight through the board. You will have 8 holes -- two sets of four on each end.
How to make your skateboard trucks loose?
  • Turn it clockwise to tighten the trucks, getting tighter turning.
  • Turn it counter-clockwise to loosen the trucks, getting a softer turning feel.
  • Make sure you tighten the trucks in very small increments (perhaps a quarter of a turn at a time before checking the board again), because a little bit of turning ...
Do skateboard trucks come with wheel nuts?

Skate hardware is the nuts and bolts that hold your trucks onto your deck. They come in a variety of shapes, sizes, fitments, and colors. Unlike other skate components, you don’t really get manufacturers that only produce skate hardware, the best skate hardware is usually made by Truck or Wheel companies. Size & Diameter

8.25 skateboard what size trucks?

Size Guide - Skateboard Trucks

Skateboard Truck Size Guide
Deck SizeHanger WidthAce
7.5 to 7.75"127mm / 5"22
7.75 to 8.25"137mm / 5.25"33
8.25 to 8.75"149mm / 6"44
What are high skateboard trucks?

High Skateboard Trucks

High trucks are better for turning as the truck can pivot further as the different geometry allows more movement. Larger wheels can be fitted without wheel bite, 53mm to 58mm, as the axle now sits further away from the deck.

What are hollow skateboard trucks?

Hollow Skate trucks are made using standard contruction materials, steel axles with aluminum hangers and baseplates. 'Hollow' is refering to the King pin and / or Axle being hollow. Having hollow steel components gives your board a lighter feel, that will pop higher and flip quicker.

What are low skateboard trucks?

Low Skateboard Trucks

Low trucks are generally for tech skating as the wheels sit closer to the board, creating a tighter center of gravity, making flip tricks a bit easier. You'll want to ride smaller wheels, 48mm to 53mm, to avoid wheel bite.

What are some skateboard trucks?
  • Ace 33.
  • Independent 139 Stage 11 Forged Hollow.
  • Venture Polished 5.2 Hi.
  • Ace 44.
  • Independent 144 Polished Mid.
What companies make skateboard trucks?
  • #01: Thunder Trucks. One thing is clear, you guys love Thunder trucks…
  • #05: Royal Trucks…
  • #04: Tensor Trucks…
  • #03: Venture Trucks>/h3> ...
  • #02: Independent Truck Co…
  • #01: Thunder Trucks…
  • #05: Royal Trucks.
What size are skateboard trucks?
  • Standard skateboards range in width from of 6.5 to 8 inches and in length from 28 to 33 inches. The skateboard trucks will be the same width as the skateboard they are on.
What skateboard trucks are lightest?

The lightest skateboard trucks are the Tensor Mag Light Lo weighing 9.3 oz (8″, 231 grams) ...

Which trucks skateboard?

Due to the availability of skateboard trucks from a few top-rated brands like Independent, Thunder, Bullet, Tensor, Tracker, Tandem, it's very confusing for the buyers to understand what is the best brand of skateboard trucks.

Why are skateboard trucks called trucks?

This etymology almost certainly comes from analogy with the trucks, also known as bogies, on railroad cars. The trucks on a railroad car consist of an assembly of wheels, axles, bearings, and suspension, pivoted flexibly underneath the deck and ch...

How do you tell what size your skateboard trucks are?

To determine the width of a skateboard truck, you measure the width of the axle (outer width) and the width of the hanger (inner width). The trucks should always fit the width of your Skateboard.

Are skateboard trucks as long as your board?

Bushings are the plastic pieces in the center of your trucks. The bend and are compressed when you steer your skateboard. Depending on the hardness of your bushings the help your trucks to turn smoothly. Over time bushings and pivot cups lose flexibility from steering, weather conditions, and impacts.

How long do you keep your trucks skateboard?

The angle of the baseplate plays a major role in how well your longboard handles turns. If your truck setup has a higher baseplate angle (a 50-degree angle, for instance) this allows for sharper turns because of the increased deck lean. If your skate truck setup is attached at a low angle, the trucks will turn less.

How to make your skateboard trucks turn better?

Hope you guys enjoyed this skate tutorial if you want me to make anymore just let me know comment below what kind of skate videos you want to see and what ki...

How to tighten your trucks on a skateboard?

Fixing Loose Trucks 1. Know that truck tightness is a matter of personal preference. At the end of the day, there is no "perfect" amount to... 2. Grab a board you like, flip it over, and test the trucks by tilting them back and forth. The amount the wheels tilt... 3. Use a skate tool or other useful ...